+86 591 8379 6881

Optical Inspection Procedure

SUPERIOR OPTICS / CAPABILITIES

Optical Inspection Procedure

An optical inspection procedure defines what to check, when to check it, and what evidence is needed before releasing a lens or lot. Agree on the drawing revision, acceptance limits, sampling plan and required records before prototype approval or production release.

Inspection Checkpoints: From Incoming Material to Final Release

Start with incoming material inspection, then use in-process optical inspection to check critical features before later operations make them harder to verify. Add coating and assembly checks where applicable, and use final lens inspection to confirm the agreed release requirements.

  1. Incoming inspection

    Verify material identity, lot records and incoming condition.

  2. In-process inspection

    Check designated dimensions, surface form and appearance.

  3. Coating checks

    Where applicable, review spectral results and witness sample records when specified.

  4. Assembly checks

    Where applicable, check alignment, focus or imaging performance as specified.

  5. Final inspection and release

    Review results against acceptance limits and confirm release status.

Example inspection flow. Checkpoints and records depend on the product, drawing and agreed inspection plan.

Project Requirements and Deliverables

Share the current drawing, product configuration, expected quantities and critical acceptance limits. Define which checks apply to first samples and production lots, then agree on the sampling plan, measurement conditions and records needed at each stage.

Project Requirements and Deliverables
Review itemWhat to shareReview output
Incoming materialDrawing revision, component identifiers and incoming criteriaIncoming check record and lot identification
Assembly checkpointsCritical operations, limits and responsible process ownerIn-process results or documented deviations
Final acceptanceInspection method, sampling rules, and pass/fail limitsFinal report or release record as agreed
NonconformanceNotification, segregation, rework and concession rulesDisposition and retest or approval record

Technical Reference for Optical Surface Imperfections

When the drawing specifies surface imperfections, identify the surface, inspection area and applicable limit. Confirm the evaluation method and viewing conditions before inspection so both teams apply the same criteria when assessing the part.

What to Include in a Release Record

An optical inspection report should connect each result to the drawing revision, part or lot, and agreed acceptance limit. Record the inspection outcome and any unresolved deviations so the reviewer can see why the lot was released or held.

  • Trace the Part or Lot

    Record the part number, drawing revision, lot or serial number, and inspected quantity. Link each result to the sample measured and distinguish first sample approval from routine production inspection.

  • Compare Results with Limits

    List the measured value or attach the relevant plot alongside the acceptance limit. Include the method and test conditions needed to interpret the result, and identify which checks were performed on samples.

  • Document the Release Decision

    Record whether the lot was released, held or referred for review. Identify any deviation, retest result or authorized concession, and keep the decision traceable to the affected parts and inspection records.

BUYER QUESTIONS

Optical Inspection Procedure FAQ

Review common questions about first sample approval, lot sampling and nonconforming results. Use them to clarify what must be checked, which records to request, and who decides whether a lot can be released.

Does every lens need the same inspection plan?

No. Set the checks according to the product, drawing and application. A coated element and a finished imaging assembly may require different tests and records.

Which checks are sampled and which apply to every unit?

Define this by characteristic before production. Record the agreed sample size or unit-by-unit requirement and the criteria used to accept the lot.

What happens if an inspection result is outside the limit?

Identify and hold the affected parts for review. Document the result and agree on the next step, such as retesting, rework, rejection or an authorized concession.

PROJECT INQUIRY

Discuss Your Optical Inspection Requirements

Send your latest drawing, acceptance limits, lot size and reporting requirements. Identify checks required for sample approval and production release, and note any customer procedures that the inspection plan must follow.

Prepare Your Lens Inquiry

Include a model number or the information currently available:

  • Application and sensor details
  • Field of view, working distance and wavelength
  • Sample quantity or expected annual volume
  • Delivery destination and preferred schedule
Contact SUPERIOR Optics

You do not need a complete optical specification to start. Send the information currently available, along with your delivery destination and preferred schedule.