+86 591 8379 6881

Optical Coating Capability

SUPERIOR OPTICS / CAPABILITIES

Optical Coating Capability for Imaging Lenses

Define an optical coating by the job it needs to do: improve transmission, reduce unwanted reflections or support a specific spectral response. Review the substrate, wavelength band, angle of incidence and environment together, then agree on how the coating will be verified.

Glass lens elements in an open vacuum chamber for optical coating

Define the Coating Requirement

Start with what the optical coating must do in the assembled lens. Define the usable wavelength band, incidence angle range and operating environment. Then agree whether the target applies to one coated surface, the complete optic or the assembled lens, since each calls for different evidence.

  • Specify the spectral goal

    State the wavelength band and whether the requirement is for average or worst-case transmission or reflection. Distinguish a per-surface target from a complete-lens target.

  • Define angle and environment

    Include angle of incidence and polarization where relevant. Describe handling, cleaning and operating exposure when durability is part of acceptance.

  • Agree on verification

    Decide whether to review a witness sample, a coated part or the finished lens. Specify the test conditions and the records that must accompany approval.

Compare Optical Coating Options

Choose the coating by the optical function it must perform. Compare anti-reflection coatings, spectral filters and reflective coatings against your wavelength band and working angles. For each option, define what should pass or reflect, where it should do so, and how you will measure it.

Compare Optical Coating Options
OptionWhen to evaluate itWhat to specify
Narrowband anti-reflectionA single wavelength or narrow operating band dominates.Design wavelength, band limits, incidence angle and maximum reflectance per surface.
Broadband or dual-band anti-reflectionImaging uses a wide continuous band or two distinct bands, such as visible and near infrared.Define each band separately and specify average and maximum reflectance as needed.
Spectral filter coatingThe optic must transmit selected wavelengths and reject others.Passband transmission, stopband blocking, edge wavelengths and applicable angles.
Reflective or partial-reflective coatingThe optical path requires a mirror or a specified reflection-to-transmission split.Band, angle, polarization and reflection or transmission limits for the intended optical path.

Technical Reference for Coating Durability

Specify durability tests around how the coated optic will be handled, cleaned and exposed in service. Use ISO 9211-3 as a reference when applicable, then agree on the test conditions, sample type and pass criteria before the build so the results can support the acceptance decision.

Substrate Preparation and Deposition Review

A coating review starts with the actual substrate, not just a target curve. Agree on cleaning and handling, areas to mask, fixture access and temperature limits before comparing deposition methods. Confirm which steps and tests apply to the sample and whether the same process will be used for production.

  • Prepare and protect the optic

    Identify material grade, surface finish, coatings already present and permitted cleaning methods. Mark clear apertures, edge exclusions and faces that must remain uncoated.

  • Compare deposition routes

    Where relevant, discuss evaporation, ion-assisted deposition or sputtering as candidate methods. Ask the coater to confirm substrate compatibility, fixture needs and the evidence available for the proposed process.

  • Plan sample handling

    Agree on sample identification, protection of coated surfaces and how appearance or damage will be checked before packing. Confirm responsibilities for any externally performed steps.

Project Requirements and Deliverables

For an optical coating quote, share the drawing, substrate, surfaces to coat, clear aperture and expected quantities. Include the target spectrum with its test conditions, plus any handling or durability requirements. Mark open items so the quotation can state the proposed scope, test samples and acceptance criteria.

Project Requirements and Deliverables
Review itemWhat to shareReview output
SubstrateMaterial grade, surface geometry and clear apertureCoating compatibility and handling review
Spectral requirementBand, transmission or reflection target, angle and polarizationDefined coating target and test conditions
DurabilityCleaning method, environment and relevant test requirementsAgreed durability evidence, if required
ApprovalWitness sample or part measurement, quantity and lot recordsSample verification and release documentation

Coating Verification and Approval

Agree how the optical coating will be accepted before authorizing samples. Match spectral measurements to the specified wavelength band, incidence angle and polarization. Define what a witness sample can demonstrate, what needs to be checked on the actual optic or assembly, and how reports will trace back to the coating run.

  • Spectral evidence

    Record the coated side, sample ID, wavelength band, incidence angle and polarization where relevant. Compare the measured transmission or reflection curve with the agreed average and worst-case limits across each band.

  • Durability evidence

    Define which exposure or cleaning tests represent the application. Agree on the specimen, conditions and pass criteria, and record any visual or spectral changes required by the acceptance plan.

  • Lot traceability

    Link witness samples, measured optics and reports to the applicable coating run and drawing revision. Record deviations and agree which checks must be repeated after a change in substrate, fixture or process.

BUYER QUESTIONS

Optical Coating FAQ

Find out what to specify for visible and near-infrared imaging, when to test the actual optic and how to define durability before approving samples.

Is there one AR coating for every imaging lens?

No. Start with the wavelength band, substrate and incidence angles. A visible-light requirement and a visible-plus-NIR requirement need separate review.

Does a witness sample represent the finished lens?

It can help characterize a coating run. Agree separately on whether the actual part or full lens also needs testing.

How should coating durability be specified?

Describe the environment and cleaning conditions. Where a standard or test method applies, agree on the revision and pass criteria before the build.

Can the same coating be used at a different angle?

Review the curve at the new angle and specify polarization if it matters to the application. A result measured at normal incidence does not establish performance over a wider working angle range.

What should a coating RFQ include?

Send the material, drawing revision, surfaces to coat, clear aperture, angle range and spectral limits. Include required durability tests and state whether evidence is needed on a witness sample, the actual optic or the finished lens.

PROJECT INQUIRY

Discuss Your Optical Coating Project

Send the optic drawing, substrate, wavelength band and working angles, plus your spectral targets and estimated quantities. Include any durability or reporting requirements before we review the project.

Prepare Your Lens Inquiry

Include a model number or the information currently available:

  • Application and sensor details
  • Field of view, working distance and wavelength
  • Sample quantity or expected annual volume
  • Delivery destination and preferred schedule
Contact SUPERIOR Optics

You do not need a complete optical specification to start. Send the information currently available, along with your delivery destination and preferred schedule.