+86 591 8379 6881

SWIR Inspection

SUPERIOR OPTICS / APPLICATIONS

SWIR Inspection

SWIR Inspection starts with a sample test. Compare acceptable and defective material under candidate wavelength bands and lighting geometries, then confirm that the contrast remains useful at production speed. Check the camera response, lens transmission, and any filters together rather than assuming a wavelength that works on one sample will work on all runs.

Industrial SWIR Inspection camera above material samples on a conveyor, with a monitor showing sample images

What Can SWIR Inspection Reveal

SWIR Inspection can help distinguish materials or defects that look similar in visible light. Use the scenarios below to select representative samples and decide where to test wavelength, illumination angle, and exposure.

Angled lights and a SWIR camera above four material samples for moisture and coating contrast tests

Moisture and Coating Contrast

Compare samples with known moisture or coating levels. Check whether the separation remains visible across normal thickness and finish variation.

SWIR camera aimed at six material coupons on an optical bench for material comparison

Material Differentiation

Test visually similar polymers or substrates from several batches. Compare the contrast under candidate wavelength bands before deciding which band to use.

SWIR line scan camera and light bar above a moving roll of reflective film

Moving Web Surface Inspection

Test acceptable and defective samples with the intended lighting geometry and line speed. Check for glare, blur, and contrast changes near the edges.

What to Validate Before Deployment

SWIR Inspection depends on the full optical path. Use known-good and known-defective samples to measure contrast, then confirm that the result remains useful across operating speeds and normal production variation.

  • Representative Samples

    Test known-good, borderline, and defective samples from several batches. Include normal differences in finish and thickness.

  • Wavelength Band

    Compare candidate bands using the actual sensor, lens, and filters. Record which band separates acceptable and defective samples most reliably.

  • Lighting Geometry

    Compare reflected and transmitted light where practical. Adjust the lighting angle to control glare without losing defect contrast.

  • Production Exposure

    At production speed, verify that exposure limits motion blur while preserving defect contrast. Check lighting uniformity from center to edge.

Related Lens Options

SWIR Inspection requires optics matched to the actual sensor and wavelength band. Compare verified transmission and focus in the intended setup, including any filters or protective windows. Confirm image sharpness across the field at your working distance.

SWIR Inspection

SWIR Lenses

Choose a lens for your operating band and sensor format. Verify transmission, focus, and edge detail with the intended illumination, filters, and protective window in place.

Browse SWIR Lenses

Infrared Lenses

Compare models with documented transmission and focus in your target infrared band. Confirm image coverage and sharpness at your working distance before choosing a lens.

Browse Infrared Lenses

SWIR Inspection Engineering Guides

Use these guides to check that the lens covers the active sensor area and test whether defects stand out consistently on representative samples. Then match the illumination, lens transmission, and sensor sensitivity to the wavelength band that gives the best contrast for your inspection.

BUYER QUESTIONS

Frequently Asked Questions

Answers to common SWIR Inspection questions about choosing optics and verifying the finished setup.

Does SWIR always show moisture or coating differences?

No. Contrast depends on the material, wavelength, thickness, lighting, and sensor. Test samples with known differences first.

How do I choose the wavelength band?

Compare bands on acceptable, borderline, and defective samples with the actual camera and optics.

Can I use a visible-light lens for SWIR?

Only if transmission, focus, and image quality are verified in your wavelength band and installation.

What should I verify on a moving line?

Check contrast and exposure at production speed, including edge uniformity and realistic surface reflections.

PROJECT INQUIRY

Discuss Your SWIR Inspection Project

For SWIR Inspection, share the material, defect, candidate wavelengths, camera model, and operating speed. Include samples or comparable images where available.

Prepare Your Lens Inquiry

Include a model number or the information currently available:

  • Application and sensor details
  • Field of view, working distance and wavelength
  • Sample quantity or expected annual volume
  • Delivery destination and preferred schedule
Contact SUPERIOR

You do not need a complete optical specification to start. Send the information currently available, along with your delivery destination and preferred schedule.